Build a set of Evil twins with my New JMR Manual Bender!

[FlyHiFlyLo]

I was at the off road swap last weekend and picked up a JMR manual bender. Dudes that thing is the most ingenious tool I have ever seen! When I was at the swap meet they had a 3/8" ratchet bend 1.75x.120 chrome moly. This weekend I went ahead and chopped the old school rear portion of one rail off and built a new one to match the other in less than one day...

I already had a JMR notcher and a pro tools bender (sold the Pro tools and my cracked 1.50 die on e-bay) but this new bender is great! I could bend this 1.50x.120 mild steel in high gear, however low gear is very fast too and tended to be about half speed so I could get my bends really close to one another. A friend has a full power JMR bender and I really don't see the need for a garage guy to go that route. He has a shop so I could see why he might need to go power... But really.... I think this manual deal is more controllable than a valve.

Sure beats Looking like a monkey humping a football like I was with that long levered protools deal. You could actually take this deal out to the races and do Major repairs in the pits, I bought the stand and degree wheel but, if you had to, this thing works so good you could do it right on the ground (in race pit conditions). You don’t need a bench for leverage.

Anyways check out my Evil Duo.

[SPONSOR]

Membership in the largest desert racing community has its advantages - Participate in Forum Discussions - Send and Receive Private Messages - Maintain Public Photo Albums - Access to Groups - User Profile in our Social Network - Increased Access to more Sub Forums - Reduced Online Advertisements Join our community today

[therail]

hypothetically, of course, could you use maybe a 3/8ths impact for a little sped increase? and just leave the final few degress up to a ratchet?

[FlyHiFlyLo]

hypothetically, of course, could you use maybe a 3/8ths impact for a little sped increase? and just leave the final few degress up to a ratchet?

I asked that and they said an impact would just sit there and bang away...And they told me not to try it...(probally not good for the gears inside either) I bet a good drill would would work though. Maybe a bad-ass cordless 18V.... I will have to try it.

But in all reality...The thing works very fast as it is...You could go to full travel in probally less than 10 seconds with no sweat what so ever.

[therail]

I asked that and they said an impact would just sit there and bang away...And they told me not to try it...(probally not good for the gears inside either) I bet a good drill would would work though. Maybe a bad-ass cordless 18V.... I will have to try it.

thats probably true about just slamming away. id look into a stout 3/8 air ratchet also. they are way smoother than the impact.

also, where can i look into one of these online, i "googled" it after i posted originally, but the search only turned up this thread. lol.

[FlyHiFlyLo]

Try JMRMFG.com I'm not sure they have on the site yet...JMR said they just came out with it the week before the swap meet. I just used my standard 1/2-inch Craftsman drive with a 3/4 socket... Like I said- it turns like butter. My neighbor sure was tripping out on it too. (He’s the one who said I looked like a "Monkey Humping a Football" one time while using my old Protools bender deal.)

[therail]

thanks bro!

[FlyHiFlyLo]

thanks bro!

Cole, no prob, Anything for a fellow Robby fan!

[CRAIG_HALL]

I picked up their notcher at the swap meet, pretty sweet.I saw they have an E-bay account selling them as well--do a search for jmr bender.

[J_Lothringer]

How much was the bender???

[FlyHiFlyLo]

I worked them a little for swap meet prices. Plus I got 1 set of dies a degree wheel and a stand for my bender and my notcher I got last month. I got everything for $1850.00 and my Notcher was about 5 bills...I love my notcher...Every notch is a perfect and all I have to do is sand some flash off.

Next on my list is Dimple dies those are a really good deal. I think you get 8 sizes for 4 bills.

I'm interested to see what they want on E-bay now...hummm?