• Forum membership has its advantages....

Search results

  1. On The Edge Fabrication

    newbie, has anyone ever built there own 3or4 link rear suspension for a prerunner?

    Re: newbie, has anyone ever built there own 3or4 link rear suspension for a prerunner Deavers for sure buddy!!! Do links on your second or third build and not on a daily driver. Its the route that I went and am very thankfull that I didn't get too wild on the first one. I was and still am very...
  2. On The Edge Fabrication

    Mild steel why? Why not ?

    Get yourself a piece of each, the same diameter and wall thickness, then put them in a bender and make a bend.....you will get your answer and be blown away at how much harder it is to bend 4130. My first truck is all seamed mild steel, but after bending some 4130 for a new set of beams, I...
  3. On The Edge Fabrication

    BAJA 1000 Update Thread

    Go Pflueger 441MPH
  4. On The Edge Fabrication

    BAJA 1000 Update Thread

    hell yea!!! Here we go
  5. On The Edge Fabrication

    BAJA 1000 Update Thread

    31-B is backup tracker
  6. On The Edge Fabrication

    BAJA 1000 Update Thread

    Its getting close to live feed time!!!!!! woohoo!!!!!
  7. On The Edge Fabrication

    BAJA 1000 Update Thread

    What time do the trucks start.
  8. On The Edge Fabrication

    BAJA 1000 Update Thread

    Thanks.... I love technology
  9. On The Edge Fabrication

    BAJA 1000 Update Thread

    Is there going to be live feed of the start like last year
  10. On The Edge Fabrication

    coreless impact gun

    I got one from pep boys bout 2 years ago for 79 bucks and it works great, best tool I have ever bought that was so much cheaper then all the competitors. Goodyear racing =$79
  11. On The Edge Fabrication

    I-beam swing-set steering?

    Maybe this with show you some layout options
  12. On The Edge Fabrication

    Mounting I-beams on a tube frame?

    If you mount them 2" apart..... Then angle the drivers side forward 1" and the pass. side back one inch, to get equal wheel base.
  13. On The Edge Fabrication

    Sprint to the Dash/Bud Light Dash 2009 !

    No more saving for a house....its time to go racin' again. Can't wait its been a year off trying to get a house and do the responsible thing... too bad its not as fun as racing. 1481 will be out for the dash....back in action, finally:)
  14. On The Edge Fabrication

    Powder Puff 2009 Photo's

    Any of 8014 Thanks
  15. On The Edge Fabrication

    **Racer Photo- MORE Powder Puff**

    Looking for 8014. Thanks
  16. On The Edge Fabrication

    1450 ranger...

    http://giantmotorsports.com/content/category/4/28/43/ love the leafs. save your money and get some wheel time.
  17. On The Edge Fabrication

    Ranger Shock Question

    pre-runner= 2.5 coil and by-pass race=2.5 coil and 3.0 by-pass you don't need the by-passes unless your racing or just got lots of $$$$
  18. On The Edge Fabrication

    SBF accessory drive: Pulleys & Brackets, advice and pics needed

    dang a 650 sb....whats that going in??
  19. On The Edge Fabrication

    31's or 33's for a ranger?

    I am a big fan of 33x10.50 a lot guys run the wider ones, but i like the lighter weight with that diameter. The rules say 85 so I would go 84.5 just to be safe. i have been told that it is 85 to the outermost part of the tire.
Top